McIntosh WK-3 Manual do Proprietário Página 9
- Página / 60
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
9
Installation
The MX134 can be placed upright on a table or shelf,
standing on its four feet. It also can be custom installed in a
piece of furniture or cabinet of your choice. The four feet
may be removed from the bottom of the MX134 when it is
custom installed as outlined below. The four feet together
with the mounting screws should be retained for possible
future use if the MX134 is removed from the custom instal-
lation and used free standing. The required panel cutout,
ventilation cutout and unit dimensions are shown.
Always provide
adequate ventilation
for your MX134. Cool
operation ensures the
longest possible oper-
ating life for any elec-
tronic instrument. Do
not install the MX134
directly above a heat
generating component
such as a high pow-
ered amplifier. If all
the components are
installed in a single
cabinet, a quiet run-
ning ventilation fan
can be a definite asset
in maintaining all the
system components at
the coolest possible
operating temperature.
A custom cabinet
installation should
provide the following
minimum spacing di-
mensions for cool op-
eration. Allow at least
2 inches (5.08cm)
above the top, 2
inches (5.08cm) be-
low the bottom and 1
inch (2.54cm) on each
Installation
6 -
5/8
"
16.83cm
17-
1/16
"
43.34cm
Cutout Opening for Custom Mounting
MX134 Front Panel
Custom Cabinet Cutout
Cutout
Opening
for
Ventilation
Cutout Opening for Ventilation
Support
Shelf
Cabinet
Front
Panel
Chassis
Spacers
MX134 Side View
in Custom Cabinet
MX134 Bottom View
in Custom Cabinet
13"
33.02cm
13"
33.02cm
15"
38.10cm
1"
2.54cm
14-
1/4
"
36.20cm
10-
7/8
"
27.64cm
Notes: Center the Cutout Horitzonally on unit.
For purposes of clarity, the above
illustration is not drawn to scale.
side of the A/V Control Center, so that airflow is not ob-
structed. Allow 21 inches (53.34cm) depth behind the front
panel. Allow 1-1/8 inch (2.9cm) in front of the mounting
panel for knob clearance. Be sure to cut out a ventilation
hole in the mounting shelf according to the dimensions in
the drawing.
- IMPORTANT SAFETY 2
- INSTRUCTIONS! 2
- General Notes 5
- Connector Information 6
- Performance Features 7
- Introduction 7
- Dimensions 8
- Installation 9
- Rear Panel Video Connections 12
- How to Connect for Zone B 16
- Front Panel Displays 19
- Remote Control Push-Buttons 20
- How to Operate the Setup Mode 22
- Default Settings 23
- SETUP, con’t 25
- Loudspeaker Size 26
- How to Adjust Speaker Levels 28
- How to Change the Input Setup 30
- Figure 20 32
- Figure 21 32
- Video Inputs Source Settings 34
- Figure 26 36
- Figure 25 36
- Figure 28 38
- Figure 29 38
- How to Operate the MX134 41
- Figure 37 42
- Figure 36 42
- How to Operate the Trim Mode 44
- Figure 48 45
- Figure 49 45
- Figure 51 45
- Figure 50 45
- How to Operate Zone B 48
- How To Make A Tape Recording 48
- Note: The audio may be 49
- Remote Control 49
- General Specifications 50
- Audio Specifications 50
- TM1 AM/FM Tuner Module 52
- FM Antenna 54
- How to Operate the Tuner 55
- How to Tune Stations Manually 55
- How to Assign Preset Stations 56
- How to Optimize AM Reception 57
- FM Tuner Specifications 58
- TM1 FM and AM Specifications 58
- AM Tuner Specifications 58
- Packing Instructions 59
- McIntosh Part No. 040754 60
- McIntosh Laboratory, Inc 60
- 2 Chambers Street 60
- Binghamton, NY 13903 60
Manuais e produtos relacionados com Teclados numéricos McIntosh WK-3
(20 páginas)EVS XEDIO-CleanEdit manuals
Owner’s manuals and user’s guides for Accessories for video EVS XEDIO-CleanEdit.
We providing 1 pdf manuals EVS XEDIO-CleanEdit for download free by document types: User Manual
Comentários a estes Manuais